If you do not change the belt on your John Deere d130 Diagram lawn mower, it can wear out over time. The belt of a mower usually lasts 3-4 years. After that, you might need to change the belt of your mower. Changing your mower deck belt as necessary will keep your machine running smoothly.
How to Replace Mower Belt on John Deere d130 Diagram
There’s no definite amount of time that a mower belt is supposed to last, but increased mower use shortens the interval in which a belt needs replacement. Simply put, more use equals more wear. Lawn mower belts that are prematurely worn can occur from faulty belts or mechanical failures like a seized pulley.
Why is it Important to Change the John Deere d130 Mower Belt?
A mower is not something you use frequently, but even if it is used regularly, the belt lasts less than the whole mower. The belt of the mower tends to tear with time. Faulty belts or seized pulleys can cause a premature breakdown of a mower belt. That is why it is important to ensure the safety of your mower when you use it again.
Steps of Replacing Mower Belt
The steps of replacing the belt of your mower are given below-
Step – 1
Firstly, you have to make sure the vehicle is off, the ignition key is removed, and the spark plug wires are disconnected before changing the mower belt in order to prevent the vehicle from starting accidentally while you’re working.
Step – 2
Then you have to adjust it. You can raise or lower the height of the deck to the right size. Your riding lawn mower’s deck can be lowered to the lowest position by moving the deck lift lever.
Step – 3
In the next step, you have to remove the mower deck belt guards. The mower deck belt guards can be removed by removing the screws that hold them in place.
Step – 4
On this step, you have to take off the belt-keep rod. The belt-keeper rod around the engine pulley needs to be removed.
Step – 5
For the next step, you have to remove the idler pulley nuts and loosen them. You have to remember that you can loosen – but should not remove – the idler pulley on a riding mower deck like the one in the video. By unscrewing the screws that keep the mower deck belt guards in place, you can remove them. This will make removing the mower deck belt from around the idler pulleys much easier.
Step – 6
Next, you have to take off the mower deck belt. Remove the mower deck belt from around all the pulleys, including the deck idler pulleys. Don’t put your fingers on the idler spring or between the mower deck belt and any of the pulleys, as this could cause your fingers to get pinched or injured.
Step – 7
After that, you have to pop out the garden tool deck belt. Remove the garden tool deck belt from around all the pulleys, as well as the deck layabout pulleys. Do not place your fingers on the layabout spring or between the garden tool deck belt and any of the pulleys, as this might cause your fingers to induce pinched or lacerate.
Step – 8
Then you can install the new garden tool deck belt Route the new garden tool deck belt within the same manner because of the recent one. If you took a photograph earlier, use it for visual reference. Or, you’ll be able to ask your operator’s manual.
Step – 9
On step 9, you have to secure the pulley loony Tighten the pulley loony you unsnarled.
Step – 10
You have to replace the belt-keeper rod. Put the belt-keeper rod back in situ round the engine pulley-block in this step.
Step – 11
After that, you can place the garden tool deck belt guards back on Remount the garden tool deck belt guards.
Step – 12
Then, you have to lift the deck. Raise the deck on your riding lawn tool back to the very best position.
Step – 13
It is recommended to replace the electrical device wires and reconnect the electrical device wires in this step.
Step – 14
Next step, you have to put the key back within the ignition and begin the unit. If you are having trouble interacting with the deck of gardening tools, let it warm up a bit. It is recommended that you open your garage door even if you are operating in an extremely crowded garage.
Step – 15
In the next step, you have to make sure about the function of the interaction of the garden tool deck. Place the throttle management at full throttle to ensure interaction with the garden tool deck.
Step – 16
Check for abnormal sounds, Disengage the garden tool deck, and stay up for the garden tool deck belt to return to an entire stop. Have interaction with the garden tool deck once more. Listen for any abnormal sound.
Step – 17
Next, you need to close up your machine and disengage the garden tool deck, bring the throttle all the way down to idle, and switch off the riding lawn tool.
Step -18
After that, you have to take away the keys and electrical device wires. Remove the key and also the electrical device wires. Before checking the garden tool deck belt, ground the electrical device wire(s) against the engine to forestall the fortuitous beginning.
Step – 19
Then, you have to lower the deck and adjust the deck to an all-time low position and examine the garden tool deck belt. Check the garden tool deck belt to confirm it’s properly running through all the pulleys, which does no harm.
Related Article: Best 34 Inch Zero Turn Mower
Step – 20
In the last step, you have to reconnect the electrical device wires. Once you have modified your garden tool deck belt and checked your work, you’ll be able to re-install the electrical device wires.
So, these were the basic steps of changing or replacing any mower belts when needed, including the John Deere d130 Diagram. The only thing you have to make sure of is using the same belts for the mower model for best performance. If you still face any kind of problem while changing the belt of your mower then, it is advised to seek help from the experts. You can also check out some websites where there are pictures given with the steps for better understanding.