6 Most Common Echo CS-310 Problems and Solutions

Echo CS-310 is a low powered gas chainsaw that is best for light works. However, inspite of being low powered it delivers powers in a significant amount which is 30.5cc and 1.86 horsepower. It is very compact and lightweight so you can carry it easily. This chainsaw by Echo has excellent maneuverability and good fuel efficiency. It is sold with a 14-16 inch bar.

Despite its amazing features, you might find some issues that are common with this machine. Not running properly, starting then stopping, dies when inserting gas, bogs down at full throttle, chainsaw misfires, stall out when idling, bad spark plugs are some of the common problems that a user might face with the Echo CS-310 chainsaw. So, in this article we are going to talk about the common problems, so that you can solve them easily.

6 Common Problems of Echo CS-310:

Whether you have an Echo CS-310 chainsaw or you are thinking of buying this model, you should be aware of the drawbacks you might face. However, the drawbacks do not make it a bad chainsaw because as soon as you fix hte issues, it will be good as new. When you are aware of the reasons that are causing the problems, you will be able to solve them easily.

So, the common problems of Echo CS-310 are discussed below:

1. Not running properly

If you experience you chainsaw suddenly stops after running spme time, then it has running issues. It can happen due to faulty or damaged spark switched or plugs, bad fuel and blocked carburetor.

To solve this running issue, you need to check the carburetor first. It might get clogged because of not cleaning it for a long time, or leaving fuel in the chainsaw for a long time without using it. In this way, some of the fuel’s constituents may dissolve over time, leaving behind a heavier, thicker material. The carburetor might become clogged with this sticky gasoline, causing the chainsaw motor to stall.

If this does not solve your problem, then you can check the spark plugs and spark switches. If they are damaged or faulty, replace them with new ones. Ad check the fuel too. If it is bad, then drain it and refill it.

2. Dies when inserting gas

If you experience issues like the chainsaw dying when you are putting gas or fuel in it then this can also be caused by clogged and dirty carburetor. Ao, if the fuel filter is clogged, then enough fuel would not be able to reach the fuel tank and it can become more clogged than before. As a result, the chainsaw dies when you try to run it, although you have just refilled the gas or fuel.

This issue can sometime crank up the whole power, or partially powering the chainsaw so it idles and stalls, or dies after some time. If you face this situation then the only option you have is to clean the clogged fuel filter. Or else it can damage the engine too. 

3. Bogs down at full throttle

There are a number of reasons why your saw bogs down at full throttle or when accelerating. It’s possible that the carburetor, spark arrestor, or air filter are clogged. It’s also possible that the carburetor adjustment slipped.

4. Chainsaw Misfires

Your chainsaw spark fuse will not be able to produce the spark that ignites the gasoline if it is broken or worn, causing the engine to misfire. The ignition coil and the spark plug have a close relationship, which might cause the engine to misfire.

To solve the issue you need to remove the plug with a spark plug socket to have a good look at it. You will be able to figure out what caused the fire by looking at the damage. If the spark plug is just worn out, it may be replaced. Make sure fresh spark plugs are replaced and gapped appropriately.

5. Stall out when idling

The idle setting should be adjusted if the engine dies while idling. Adjust either the low-speed or high-speed modulation scheme to increase performance if the engine doesn’t stall until you compress the pedal.

To make your chainsaw function effectively, your chainsaw’s engine need a sufficient supply of air. Your chainsaw may not start or continue running because of a blocked air filter. Remove the air filter from your chainsaw. Wash it or replace it if it is blocked or too dirty.

6. Bad spark plugs

One of these malfunctioning parts in the fuel system might generate a poor spark on a Husqvarna chainsaw. Most spark troubles may be avoided by properly maintaining and cleaning the saw on a regular basis. The majority of issues can be simply isolated and resolved with a few simple tooling.

Use a soft wire brush to gently clean any section of your spark plug that has a dark-colored accumulation of carbon. Ensure that all carbon has been removed from both ends. If the plug is covered in an oily residue, wash it with warm water and soap. A contemporary spark plug is unaffected by water.

If your failed spark plug is physically broken, or if it appears to be in good working order but isn’t sparking, just replace it. Spark plugs are inexpensive, and replacing a broken one is difficult. Make that the replacement plug has the same thread pattern as the old or even the same depth of penetration.

Frequently Asked Questions

Why does my chainsaw stall out when idling?

The idle setting should be adjusted if the engine dies while idling. Tighten either the low-speed or high-speed adjustment screw to increase performance if the engine doesn’t stall until you compress the throttle.

Should you start a chainsaw with the chain brake on?

Always start a chainsaw with the chain brake engaged to ensure that the chain does not move.

Are Echo chainsaws made in China?

Gas chainsaws are ECHO’s most popular product, but the company also offers battery chainsaws and a variety of other outdoor power equipment such as blowers, brush cutters, and hedge trimmers. ECHO chainsaws are designed and built in Japan, China, and the United States.

Final Words

Echo CS-310 is one of the best chainsaws in the market despite the little drawbacks. It is very durable and easy to use. The little drawbacks are also easy to resolve. So, if you are thinking about buying this model you can surely give it a try.

Leave a Comment